DC07 Spares

COMPATIBLE 9.4M CABLE 1.0MM 2 CORE

9.4M Vacuum Cleaner Hoover Mains Power Flex Cable Lead & Plug For Various Models & BrandsCompatible With Dyson Models Below:DC01, DC03, DC04, DC07, DC14, DC33 (Please Note: this Cable is Pacifically for the DC14 Models however if you change the terminals on the ends you can make these fit above models and further below Brands.Vax, Hoover, Henry/Hetty etcLength - 9.4M2 Core1.0mmColour - GreyComes complete with plug and quality rubberised casing

DYSON BIN FLAP (NO SEAL)

This part will fit all versions of the Dyson DC07 vacuums, even if yours is a different colour. THESE ARE SENT AT RANDOM DUE TO LIMITED STOCK, DISPLAY PICTURE IS A STOCK PHOTO TO SHOW YOU THE PART

DYSON BRUSH ROLL (BRUSHBAR) FOR CLUTCHED VACUUMS

This Brush bar is suitable for the below Dyson models onlyDC07, DC14, DC33This brushroll is for machines with a clutch. If you are not sure if your Dyson has a clutch or not, or dont know what a clutch is, On your Footplate where you fold the vacuum back there should be a colored dial next to it or on the opposite side, which you turn backwards to stop the brush from spinning, this is called a Clutch. If yours does not have this then you require a Clutchless BrushRoll which can be found on our Page.If Genuine not available bristles on compatible brushbar will either be purple or Blue depending on Stock, Our Compatible ones are just as good as the Genuine.

DYSON CLUTCH BELT SET

These belts are only for the clutched versions stated below. Dyson DC03, DC04, DC07, DC14, DC33, DC27Set includes:1 x Small belt1 x Large BeltCompatible Belts are made to the same specification as the original beltsCompatible Belts are made from american rubber making them very strong and stretch-able for easier fitting.*PLEASE NOTE: THESE BELTS WILL FIT AS STATED, THEY WILL ALSO BE SMALLER THAN THE BETLS ON YOUR OLD CLUTCH, DUE TO THE OLD BELTS BEING STRETCHED OVER THE YEARS. IF YOU YOU FIND THESE BELTS TO TIGHT TO FIT, THAT IS BECAUSE EITHER YOU HAVE ORDERED THE WRONG ONES, OR STRUGGLING TO FIT THEM (NON FAULT OF THE PARTS). PLEASE ONLY BUY IF YOU ARE CONFIDENT IN FITTING THEM*

DYSON CLUTCHLESS AND SOLEPLATE KIT

Brush Bar and Soleplate + 2 X BELTSThere's Nothing quite like perfection but as these are no longer made by dyson anymore their is now Low Stock Get yours as a spare while you can

DYSON CLUTCHLESS BRUSH BAR

Dyson DC04/07/14 Non Clutch Brush Bar & Belt Service Kit (2x Rubber Belts included)

DYSON CLUTCHLESS FOOTPLATE

Dyson Footplate to fit below Dyson Clutchless Models:DC04 - DC07- DC14Low Stock, Once There Gone There Gone

DYSON DC07 CYCLONE BIN FLAP PUSH ROD

Dyson DC07 HEPA Filter Kit

Filter Kit For Dyson DC07 Models only If your vacuum has a white post filter instead of purple filter you can find the filter kit for these in our Dc07 category If you are only after the hepa filter we recommend buying the kit instead because1) you will save money plus have a spare washable Pre filter 2) we recommend changing both filters at the same time for better performance.DID YOU KNOW?The washable Pre filter for a Dc07 also fits a Dyson DC33 Model

Dyson DC07 Pre Filter (Washable)

This is the filter that is located at the side of the motor. It will fit all versions of the DC07 & DC33. The filter is fully washable so that it can be used again and again. Some customers however like to buy more than one so they always have a spare

DYSON DC07 VACUUM CLEANER WAND HANDLE

COLOUR IS SILVER/DARK SILVERThis will fit all DC07 Models.

DYSON DC07 WAND ASSEMBLY

Dyson DC07 Main Wand Handle Reclaimed Genuine - Wand colour will vary from stock picture, as these are sent at randomNew Compatible - Wand Colour will be Silver and Dark Silver 

DYSON DC07 WAND CATCH & SPRING

Dyson DC07 Wand Catch Inc Spring 

DYSON DC07 WASTE BIN TRIGGER

Dc07 Cyclone/Waste Bin Release TriggerThis will fit all dc07 ModelsPlease leave us a message or note if you are after a certain colour and we will aim to match but not guaranteed due to stock.

DYSON DC07/14/33 FILTER RELEASE CATCH

Dyson Dc07/14 & Dc33 Filter Release CatchColour is guide only to show what they look like, Colour will be sent at randomIf genuine reclaimed not available, we have New 3D Printed versions which are easier to fit and remove and only come in Grey 

DYSON DC14 CREVICE TOOL 32MM

This is a curved crevice tool that stores on the side of the DC14 vacuum.Will fit all versions of the Dyson DC14 vacuums. This will also fit DC01/DC02/DC03/DC04/DC05/DC07 Models (on the hose & wand), However it will not store on the other vacuum cleanersThis tool can also fit other branded vacuums that take a 32mm tool

DYSON INTERNAL HOSE

This is the small hose located behind the brush housing. They can split over time causing a loss of suction. Will fit all versions of DC07,DC14 & DC33 models. Will also only fit clutchless versions of the DC04. If your hose pushes on both ends then this is not the hose for you. This hose pushes on one end and screws on the other

DYSON MAINTENANCE TOOL KIT

These are not produced by Dyson, But we supply these so you have the ability to make repairs yourself if you have no one local vacuum shop to go to.Kit Contains:3 x Torx Screwdrivers - T15, T10, T81 x Belt Lifter for Dyson Clutched Vacuums Only1 x Switch Removal Tool

DYSON ON/OFF POWER SWITCH

Genuine OEM Dyson On/Off switch for the following models DC03, DC04, DC05, DC07, DC08, DC14, DC15, DC19, DC33Due to stock colour of switch might vary, however it will still do the same job and work the sameThis is a 2 prong switch that will work with most of the Dyson vacuums (not DC01, DC02 or cordless machines)The photo shows a BAR Switch however as these are sent at random due to stock you might receive a black or Brown switch insteadOEM - Original Equipment Manufacturer. These are made by Dysons original Manufacturer