DC04 Spares

Quick viewAdd to wishlist

Dyson DC03 DC04 DC07 DC14 DC27 DC33 Vacuum Cleaner Clutch Cog & Circlip

*PLEASE ONLY BUY THIS PART IF YOU ARE 100% HAPPY AND SURE WITH WHAT YOU ARE DOING. WE CANNOT ACCEPT RETURNS FOR WRONG FITTING PRACTICES*This part is the white cog complete with a new retaining clip, even if your old one looks good, we would still advise fitting the new clip included.The part is one of the most common parts to wear on the clutch, a new clutch would cost you ?30+ so getting yours fixed is the best and cheapest solution. Make sure that your belts are not stretched, if they are please see below where you can buy a set.The part is 100% compatible with all clutched versions of DC03, DC04, DC07, DC14, DC27 & DC33, there is no way that these cannot fit. Therefore if yours does not fit then we are afraid it will be the fitter at fault and not the part. So please only buy if you are happy to fit yourself or know someone who is happy to fit for you.Part is a non genuine part, names and numbers are used so that you can find the part you need

£3.99
Quick viewAdd to wishlist

Dyson DC03, DC04, DC07, DC14, DC33, DC27 Clutched 'Clutch' belts

These belts are only for the clutched versions of the models stated in the title. It includes:1 x Small belt1 x Large BeltBelts are made to the same specification as the original belts*PLEASE NOTE: THESE BELTS WILL FIT AS STATED, THEY WILL ALSO BE SMALLER THAN THE BETLS ON YOUR OLD CLUTCH, DUE TO THE OLD BELTS BEING STRETCHED OVER THE YEARS. IF YOU YOU FIND THESE BELTS TO TIGHT TO FIT, THAT IS BECAUSE EITHER YOU HAVE ORDERED THE WRONG ONES, OR STRUGGLING TO FIT THEM (NON FAULT OF THE PARTS). PLEASE ONLY BUY IF YOU ARE CONFIENT IN FITTING THEM*

£2.99
Quick viewAdd to wishlist

Dyson DC04 DC07 DC14 DC33 Vacuum Cleaner Internal Hose

This is the small hose located behind the brush housing. They can split over time causing a loss of suction. This is a after-market part that is a great alternative to genuine.Will fit all versions of DC07,DC14 & DC33 models. Will only fit clutched versions of the DC04. If your hose pushes on both ends then this is not the hose for you. This hose pushes on one end and screws on the otherEQUIVALENTTOGENUINEPARTNUMBER: 904219-05

£7.99
Quick viewAdd to wishlist

Dyson DC04 DC07 DC14 Vacuum Cleaner Soleplate Baseplate

Over the years the soleplate on the bottom of the machine can wear down, in doing so the machine will stick to the carpet more making it harder to push. The soleplate is easy to replace with only using a 2p coin (10p or 50p will also work if your feeling flush)This is a high quality alternative to Genuine.Will fit all DC04 DC07 & DC14 vacuums that do not use a clutch. If your brushbar on your DC04/07/14 is round then this will fit. If it is flat and twisted; this will not fit.

£7.99
Quick viewAdd to wishlist

GENUINE DYSON INTERNAL HOSE FITS DC04

GENUINE DYSON INTERNAL HOSE FITS DC04A genuine reclaimed part works and lasts better than a cheaper pattern new part.This is the hose that connects to the brush housing on the DC04. This will only fit DC04 models that use a clutch (dial on the side of the foot plate so that you can turn the brush on/off)If your old hose is clear with a grey rubber end that you can remove, this hose will not fit your machine, but we do have those as well.

£5.99
Quick viewAdd to wishlist

Genuine Dyson Reclaimed Dc04 Chassis Seals Inc Delivery, faster post available

This seal kit will fit all models of DC04. The complete kit is for DC04 only. So please do not order based on they look like your seals, please be sure you have a DC04 vacuum. These Seals require replacing as time goes on as they can dry out and crack, which leads them not to seal properly. We check all seals before we send them out.We are also a UK business based in Holbeach. All items sold are in the UK and will be sent direct from us.

£4.99
Quick viewAdd to wishlist

ORIGINAL QUALITY DYSON DC01, DC04,DC07,DC14 VACUUM CLEANER BELTS 2 PACK

If the belt on your Dyson has snapped, there is no need to worry. These belts are not only easy to fit, but because they are made to the same quality as a genuine part, you are getting great belts at a low cost.Each pack contains 2 belts (keep one as a spare)To Fit: Place round the brush roll first, then stretch the belt over the motor spindle.Please Note: Please check that your brush spins freely before fitting, also make sure to look for any damage. Once fitted check to make sure that the belts have not got twisted when fittingMODELFITMENT: DC01,DC04,DC07,DC14

£2.99