If your Dyson is not picking up like it use to then one of the issues could be the brush bar. Over time the bristles can get shorter, and if hair and string is not removed it can also cause the bristles to break. This brush bar will fit the following models listed below:DC03DC04 (Clutched only)DC07 (clutched only)DC14 (clutched only)DC33 All models*Please note that you may need to use your old end caps for DC03 & DC04 models*If you are unsure if this will fit your vacuum then please do drop us a message£8.99
Dyson DC14 Vacuum Cleaner Wand Handle Cap
This is the wand cap located at the top of the wand. It is not uncommon for these to get knocked off.
Will fit all versions of the DC14, however, the colour of yours may be different, unfortunately you can only get one colour now. It will not affect its function though.
Genuine Dyson product
*PLEASE ONLY BUY THIS PART IF YOU ARE 100% HAPPY AND SURE WITH WHAT YOU ARE DOING. WE CANNOT ACCEPT RETURNS FOR WRONG FITTING PRACTICES*This part is the white cog complete with a new retaining clip, even if your old one looks good, we would still advise fitting the new clip included.The part is one of the most common parts to wear on the clutch, a new clutch would cost you ?30+ so getting yours fixed is the best and cheapest solution. Make sure that your belts are not stretched, if they are please see below where you can buy a set.The part is 100% compatible with all clutched versions of DC03, DC04, DC07, DC14, DC27 & DC33, there is no way that these cannot fit. Therefore if yours does not fit then we are afraid it will be the fitter at fault and not the part. So please only buy if you are happy to fit yourself or know someone who is happy to fit for you.Part is a non genuine part, names and numbers are used so that you can find the part you need£3.99
These belts are only for the clutched versions of the models stated in the title. It includes:1 x Small belt1 x Large BeltBelts are made to the same specification as the original belts*PLEASE NOTE: THESE BELTS WILL FIT AS STATED, THEY WILL ALSO BE SMALLER THAN THE BETLS ON YOUR OLD CLUTCH, DUE TO THE OLD BELTS BEING STRETCHED OVER THE YEARS. IF YOU YOU FIND THESE BELTS TO TIGHT TO FIT, THAT IS BECAUSE EITHER YOU HAVE ORDERED THE WRONG ONES, OR STRUGGLING TO FIT THEM (NON FAULT OF THE PARTS). PLEASE ONLY BUY IF YOU ARE CONFIENT IN FITTING THEM*£2.99
This is the small hose located behind the brush housing. They can split over time causing a loss of suction. This is a after-market part that is a great alternative to genuine.Will fit all versions of DC07,DC14 & DC33 models. Will only fit clutched versions of the DC04. If your hose pushes on both ends then this is not the hose for you. This hose pushes on one end and screws on the otherEQUIVALENTTOGENUINEPARTNUMBER: 904219-05£7.99
This motor will fit all DC07, DC14, DC27 & DC33 models with the following printed on their motors YV-511, YV-2200,YV-16K24EC, YV-16K24EE, YV-16K24ED. It will also fit all DC04 models that use a YDK motor. If yours is a black Ametek motor then you will need the conversion kit as well (please find that below)£19.99
Dyson no longer make this part, we however can offer this great after-market alternative. This filter will fit all versions of the models listed in the title and is fully washable. The filter is two parts:1 x Yellow Casing1 x Blue Foam InsertYou will receive both parts£4.99
This is the white filter pad located above the motor (under the clear bin). Yours may not look white, may be a grey/black colour from the years of motor carbon dust. These filters are not designed to be washed, which is why they are best to be replaced. If your filter is a thick plastic filter then you will need the HEPA filter that can be found below£2.45
Dyson no longer make these filters, however we are able to offer you these great after-market alternatives. These filters will fit all versions of the DC14 vacuums.Now yours may have a white/grey filter above the motor, the purple filter in this kit replaces that filter and offers a better filtration. However, if you would like to keep the same filter in there we also sell them in a kit or as a separate itemKit contains:1 x Pre Motor Filter (Yellow casing and blue sponge)1 x HEPA filter£7.99
This is the curved crevice tool that stores on the side of the vacuum. You can either buy the tool on its own or buy the kit which contains all 3 tools (see below)Will fit all versions of the Dyson DC14 vacuums. High quality after-market part£5.49
If the belt on your Dyson has snapped, there is no need to worry. These belts are not only easy to fit, but because they are made to the same quality as a genuine part, you are getting great belts at a low cost.Each pack contains 2 belts (keep one as a spare)To Fit: Place round the brush roll first, then stretch the belt over the motor spindle.Please Note: Please check that your brush spins freely before fitting, also make sure to look for any damage. Once fitted check to make sure that the belts have not got twisted when fittingMODELFITMENT: DC01,DC04,DC07,DC14£2.99